Unsupported Browser Detected

The Lenovo Support website supports Microsoft Internet Explorer 10+, Mozilla Firefox 29+, Chrome 34+ and any other modern web browser.

      System board and PC Card/Express Card slots (or ExpressCard/Smart Card slots or ExpressCard/7-in-1 Media Card Reader slots) bezel assemblyremoval and installation - ThinkPad T400, R400

      Important notices for handling the system board:

      When handling the system board, bear the following in mind.

      • The system board has an accelerometer, which can be broken by applying several thousands of G-forces.

        Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.

      • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
      • If a system board is dropped, you must test it, using PC-Doctor for DOS, to make sure that the HDD Active Protection still functions (see below).

        Note: If the test shows that HDD Active Protection is not functioning, be sure to document the drop in any reject report, and replace the system board.

      • Avoid rough handling of any kind.
      • At every point in the process, be sure not to drop or stack the system board.
      • If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or conductive corrugated material.

      After replacing the system board, run PC-Doctor for DOS to make sure that HDD Active Protection still functions. The procedure is as follows:

      1. Place the computer on a horizontal surface.
      2. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.

      Attention: Do not apply physical shock to the computer while the test is running.

      For access, remove these FRUs in order:

      1. Battery.
      2. Serial Ultrabay Slim device or Serial Ultrabay Enhanced device.
      3. Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter.
      4. Palm rest or palm rest with fingerprint reader.
      5. Backup battery.
      6. Keyboard.
      7. Modem daughter card (MDC-3.0).
      8. PCI Express Mini Card for wireless LAN.
      9. PCI Express Mini Card for wireless WAN.
      10. Intel Turbo Memory Minicard or wireless USB adapter.
      11. SIM card slot.
      12. Keyboard bezel.
      13. Fan assembly.
      14. CPU.
      15. LCD assembly.
      16. Base cover, USB sub card with cable, and PC Card/ExpressCard slots (or ExpressCard/Smart Card slots or ExpressCard/7-in-1 Media Card Reader slots) bezel assembly.
      17. Structure frame.

      Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
      (a) CPU
      (b) Video chip (Discrete graphics chip models only.)
      (c) MCH (Memory Controller Hub)
      (d) ICH (I/O Controller Hub)
      (e) Accelerometer chip for the HDD Active Protection System ™

      Step 1

      StepScrew (quantity)ColorTorque
      1M2 × 2.7 mm, flat-head, nylon-coated (2)Black0.167 Nm(1.7 kgfcm)

      Turn the system board over, and then disconnect the PC Card/ExpressCard slots assembly or ExpressCard/Smart Card slots assembly or ExpressCard/7-in1 Media Card Reader slots assembly (a) from the system board.

      Step 2

      When installing: Make sure that the connector of the card slot assembly is attached to the system board firmly.


      Purchase parts online


      Was this information helpful?

      Your feedback helps to improve this site.

      • Alias ID: MIGR-71525
      • Document ID: PD012904
      • Last Updated :17 Jun 2014
      • © 2016 Lenovo