Unsupported Browser Detected

The Lenovo Support website supports Microsoft Internet Explorer 10+, Mozilla Firefox 29+, Chrome 34+ and any other modern web browser.

      Memory removal and installation - ThinkPad X60, X60s, X61, X61s, X60 Tablet, X61 Tablet

      View the memory removal movie
      View the memory installation movie


      Increasing memory capacity is an effective way to make programs run faster. You can increase the amount of memory in your computer by installing PC2-5300 CL5 double data rate2 (DDR2) synchronous dynamic random access memory (DRAM) 200 pin non-parity small outline dual inline memory module (SO-DIMM), available as an option, in the memory slot on the bottom of the computer. SO-DIMMs with different capacities are available.

      • Use only PC2-5300 CL5 DDR2 SDRAM SO-DIMM memory in your computer.
      • If you install a SO-DIMM that is not supported by your computer, the computer beeps, and the system does not start.
      • You can purchase the appropriate memory option from your reseller or marketing representative.

      To install a SO-DIMM, do the following:

      Attention: Before you start installing a module, touch a metal table or a grounded metal object. This action reduces any static electricity from your body. The static electricity could damage the SO-DIMM. Be careful to avoid the metallic projections in the SO-DIMM socket area.

      1. Turn off the computer; then disconnect the ac adapter and all cables from the computer.
      2. Close the computer display, and turn it over.
      3. Remove the battery.
      4. Loosen the screws on the expansion slot cover (1); then remove the cover (2).
        memory cover removal

        If the SO-DIMM is already in the memory slot, remove it to make room for the new one by pressing out on the latches on both edges of the socket at the same time. Be sure to save it for future use.
        memory removal

      5. Find the notch on the side of the SO-DIMM you are installing.

        Attention: To avoid damaging the SO-DIMM, do not touch its contact edge.

      6. With the notched end of the SO-DIMM toward the side of the socket, insert the SO-DIMM, at an angle of about 20 degrees, into the socket (1); then press it in firmly (2).
        memory install

        Side view of memory dimm installation

      7. Pivot the SO-DIMM downward until it snaps into place.
      8. Make sure that the SO-DIMM is firmly fixed in the slot and cannot be moved easily.
      9. Replace the expansion slot cover by aligning the back side of the cover first and then tightening the screws.
        Note: When you have added or upgraded a SO-DIMM, do not use your computer until you have closed the memory slot cover. Never use the computer with the cover open.
      10. Reinstall the battery.
      11. Turn the computer over again, and reconnect the cables.

      To make sure that the SO-DIMM is installed correctly and recognized, do as follows:

      1. Turn the computer on.
      2. While the "To interrupt normal startup, press the blue ThinkVantage button" message is displayed at the lower-left of the screen, press the ThinkVantage button. ThinkVantage Rescue and Recovery screen opens.
      3. Click Access BIOS. The System Restart Required window is displayed.
      4. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.

        The "Installed memory" item shows the total amount of memory installed in your computer.

        For example, if your computer has 256 MB of memory and you install a 256-MB SO-DIMM in it, the quantity shown in "Installed memory" should be 512 MB.
      Purchase parts online


      Was this information helpful?

      Your feedback helps to improve this site.

      • Alias ID: MIGR-62804
      • Document ID: PD011473
      • Last Updated :17 Jun 2014
      • © 2016 Lenovo