Computer stops responding with a black screen when you start Windows XP
When you try to start Windows XP, the computer may appear to stop responding (hang) with an empty, black screen immediately after the power-on self test (POST) is complete and before the Windows XP logo typically appears on the screen. Back to the top
This issue may occur if one of the following conditions is true:
This issue may occur if you have a CD, a DVD or a floppy disk in your CD, DVD, or floppy drive when you start the computer.
This issue occurs if one or more of the following elements are corrupted and will not load during the boot sequence of the computer:
To resolve this issue, remove the media in your CD, DVD, or floppy drive and then restart the computer. Back to the top
This section is intended for advanced computer users. If you are not comfortable with advanced troubleshooting, you might want to ask someone for help or contact support. For information about how to do this, visit the following Microsoft Web site: http://support.microsoft.com/contactus/(http://support.microsoft.com/contactus/)
Resolution for Cause 2
To resolve this issue, you must have the Windows XP CD-ROM. If you do not have the Windows XP CD-ROM available, you have to call your computer manufacturer to troubleshoot the issue.
If you have the Windows XP CD-ROM, use one of the following methods.
Method 1: Troubleshoot the specific element that causes Windows not to load
Note This option requires that you perform multiple steps to determine the exact element that causes the issue. This option may allow for you to keep customizations in Windows.
Restart your computer in safe mode. To do this, press the F8 key while Windows is starting. Then, create a Windows XP boot disk to start the computer.
For more information about how to create a Windows XP boot disk, click the following article number to view the article in the Microsoft Knowledge Base: 305595(http://support.microsoft.com/kb/305595/ ) How to create a bootable floppy disk for an NTFS or FAT partition in Windows XP 315222(http://support.microsoft.com/kb/315222/ ) A description of the Safe Mode Boot options in Windows XP If you can start the computer from the boot disk without receiving an error message, the damage is limited to the master boot record, the boot sector, or the NTLDR file. After Windows XP is running, immediately back up all data before you try to fix the boot sector.
Use Disk Management to view the partition information and to verify that the disk partition (or partitions) is correct. To use Disk Management, follow these steps:
Click Start, right-click My Computer, and then click Manage.
Expand Storage, and then click Disk Management.
If invalid partitions are present or you cannot start your computer by using a boot disk, consider reinstalling Windows XP on your computer and restoring your data and configuration information from a recent backup.
If you do not have a current backup copy of the data on the computer, contact a computer specialist to determine the best method of data recovery and configuration.
Run a current virus scanning program to verify that no virus is present.
Repair the master boot record by using the FIXMBR command from the Windows XP Recovery Console.
For more information about how to use the Recovery Console, click the following article number to view the article in the Microsoft Knowledge Base: 307654(http://support.microsoft.com/kb/307654/ ) How to install and use the Recovery console in Windows XP Note For more information about an error message that you may receive when you use the FIXMBR command, click the following article number to view the article in the Microsoft Knowledge Base: 266745(http://support.microsoft.com/kb/266745/ ) Error message when you run fixmbr command Warning If your computer is infected with a virus and you use the FIXMBR command, you may be unable to start the computer. Before you use this command, make sure that the computer is not infected with a virus.
If the primary boot partition is a FAT partition, use the FIXBOOT command from the Windows XP Recovery Console to write a new boot sector on the system partition, and then use the FIXMBR command to repair the master boot record.
Method 2: Repair your Windows installation
Note Repairing your Windows installation may change the configuration of Windows. You may also have to follow this step if you complete all the troubleshooting in steps option 1 and the problem is not resolved.
Use the Windows XP CD-ROM to start your computer. On the Welcome to Setup screen, press ENTER to set up Windows XP.
Press F8 to agree to the license agreement.
Use the ARROW keys to select the Windows XP installation that you want to repair, and then press R.
Windows XP Setup repairs the installation files, Windows XP automatically restarts, and then the Setup program finishes the repair of your Windows XP installation.
Follow the remaining steps to set up Windows.
Note You must have your 25-character product key to complete these steps.
As soon as this issue is resolved, make sure that the firewall is enabled, and then visit the following Microsoft Web site to reinstall the latest updates: http://update.microsoft.com/(http://update.microsoft.com/)
Run a virus scan on the computer because problems with corrupted elements can be attributed to viruses.
For more information about the Recovery Console, click the following article number to view the article in the Microsoft Knowledge Base: 229716(http://support.microsoft.com/kb/229716/ ) Description of the Windows 2000 Recovery Console 235364(http://support.microsoft.com/kb/235364/ ) Description of the SET command in Recovery Console 310497(http://support.microsoft.com/kb/310497/ ) How to add more power to Recovery Console by using Group Policy in Windows XP Professional If the articles listed here do not help you resolve the problem or if you experience symptoms that differ from those that are described in this article, search the Microsoft Knowledge Base for more information. To search the Microsoft Knowledge Base, visit the following Microsoft Web site: http://support.microsoft.com(http://support.microsoft.com) Then, type the text of the error message that you receive, or type a description of the problem in the Search Support (KB) field. Back to the top