|Acoustics||LWAD = 4.5 bels or less*|
|Dimensions (monitor and stand)||Weight: 13.2 lb (6.0 kg)|
Height: 20.0 in (507 mm)**
Width: 16.1 in (408 mm)
Depth: 8.9 in (225 mm)
|Display size and viewable area||19.0 inch (483 mm)|
|Maximum viewable area||378 x 303 mm|
|Maximum Resolution/pixel rate (Hz)||1280 x 1024/135 MHz|
|RGB vertical stripe pixel pitch||0.29 mm|
|Brightness (typical)||250 cd/m2|
|Contrast (typical)||1000 : 1|
|Colors||> 16.0 million|
|Cell response time (typical)||20 ms|
|Power requirements||Input voltage||100 to 240 V AC +/- 10%|
|Frequency||50/60 Hz +/-3 Hz|
|Power consumption (Normal)||< 40 watts|
|Power consumption (VESA Standby)||<2 watts|
|Power consumption (VESA Suspend)||<2 watts|
|Power consumption (VESA Off)||<1 watts|
|Maximum earth leakage current||< 3.5 mA at 264 V/< 0.25 mA at 100 V|
|Power cord - detached||1.8 m|
|Viewing angle||Swivel: +/- 45 degrees|
Horizontal: +/- 85 degrees
Tilt: 0 degrees forward/30 degrees backward
Vertical: +/- 85 degrees
|Pivot||Yes (graphic card dependent)|
* The noise emission level stated is the declared (upper limit) A-weighted sound power level, in bels, for a random sample of monitors. All measurements are made in accordance with ANSI S12.10 and reported in conformance with ISO/DIS 7779.
**Dimension is for maximum lift. The height at minimum lift is 15.6 inches (397 mm).
Note: Actual power consumption depends on the screen mode used, the images displayed, and how user controls are set.
- MPR-3 (Sweden)
- ISO 13406 Part 2
- ENERGY STAR (U.S.)
- Microsoft Logo - Windows 2000/XP
- Supported display modes are a function of the attaching system unit and video subsystem. The full range of display modes available with these monitors may not be available or supported with all combinations of system units, their operating systems, video adapter cards, and application software.
- Horizontal- and vertical-synchronization signal timings are critical in order to achieve acceptable screen images. As a consequence, support for all possible variations in H- and V-sync timings for any display mode cannot be assumed.
- Adjustment of the user controls to enlarge the image to its maximum size requires that the signal timings of the display mode being used fall within the monitor-timing specifications.
- The number of colors shown in any display mode will exceed 16 million and dependent on the capabilities of the video adapter in the system unit.
- The ThinkVision L192p provides FCC class B - residential installation - compliance in all display modes.
- Implementation of monitor power management follows the VESA DPMS standard. This standard must also be implemented in the attaching system unit hardware and software for monitor power management to be effective. The system implementation must provide user-adjustable, power-down delay periods. The monitor power management function is invoked only after appropriate signals are received from an attached system unit or video adapter.
- Implementation of monitor Plug and Play follows the VESA DDC standard. This standard must also be implemented in the attaching system unit hardware and software for monitor Plug and Play to be effective.
- Certain functions require the system unit to be similarly configured, so all monitor functions may not be enabled when attached to a particular system unit.
- A 19.0-inch TFT monitor has nearly 4.0 million subpixel transistors laid over an area exceeding 175 square inches. Cost-effective manufacturing processes introduce a small number of defective subpixel transistors. The L192p meets the ISO 13406-2 Class 2 Pixel Defect Standard.
- Use of 50% gray background is not recommended since some users may see undesireable FOS effects.
- The Auto-Setup "test pattern" can be used with Windows 3.1, Windows NT 3.5, Windows NT 4.0, Windows 95, Windows 98, Windows 2000, and DOS 7.0 only.