Print
login Cuenta
Search

Numeric error codes - ThinkPad T510, T510i, W510

 
Error CodeSymptom or errorFRU or action, in sequence
0175Bad CRC1, stop POST task—The EEPROM checksum is not correct.System board.
0176System Security—The system has been tampered with.
  1. Run BIOS Setup Utility, and save the current setting by pressing F10.
  2. System board.
0177Bad SVP data, stop POST task—The checksum of the supervisor password in the EEPROM is not correct.System board.
0182Bad CRC2. Enter BIOS Setup and load Setup defaults.—The checksum of the CRS2 setting in the EEPROM is not correct.
  1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10.
  2. System board.
0185Bad startup sequence settings. Enter BIOS Setup and load Setup defaults.
  1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10.
0187EAIA data access error—The access to EEPROM is failed.System board.
0188Invalid RFID Serialization Information Area.System board.
0189Invalid RFID configuration information area—The EEPROM checksum is not correct.System board.
0190Critical low-battery error
  1. Charge the battery pack.
  2. Battery pack.
0191System Security—Invalid Remote Change requested.
  1. Run BIOS Setup Utility, and then save current setting by pressing F10.
  2. System board.
0192System Security— Embedded Security hardware tamper detected.System board.
0199System Security— Security password retry count exceeded.
  1. Run BIOS Setup Utility, and then save the current setting by pressing F10.
  2. System board.
01C9More than one Ethernet devices are found. Remove one of them. Press Esc to continue.
  1. Remove the Ethernet device that you installed; or press Esc to ignore the warning message.
  2. System board.
01CAMore than one Wireless LAN devices are found. Remove one of them.
  1. Remove the wireless LAN device that you installed.
  2. System board.
0200Hard disk error—The hard disk is not working.
  1. Reseat the hard disk drive.
  2. Load Setup Defaults in BIOS Setup Utility.
  3. Hard disk drive.
  4. System board.
021xKeyboard error.Run interactive tests of the keyboard and the auxiliary input device.
0220Monitor type error—Monitor type does not match the one specified in CMOS.Load Setup Defaults in BIOS Setup Utility.
0230Shadow RAM error—Shadow RAM fails at offset nnnn.System board.
0231System RAM error—System RAM fails at offset nnnn.
  1. DIMM.
  2. System board.
0232Extended RAM error— Extended RAM fails at offset nnnn.
  1. DIMM.
  2. System board.
0250System battery error—System battery is dead.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0251System CMOS checksum bad— Default configuration used.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
0252Password checksum bad—The password is cleared.Reset the password by running BIOS Setup Utility.
0260System timer error.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
  3. System board.
0270Real-time clock error.
  1. Charge the backup battery for more than 8 hours by connecting the ac adapter.
  2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
  3. System board.
0271Date and time error—Neither the date nor the time is set in the computer.Run BIOS Setup Utility to reset the time and date.
0280Previous boot incomplete— Default configuration used.
  1. Load “Setup Default” in BIOS Setup Utility.
  2. DIMM.
  3. System board.
02F0CPU ID:xx Failed.
  1. CPU.
  2. System board.
02F4EISA CMOS not writable.
  1. Load Setup Defaults in BIOS Setup Utility.
  2. Replace the backup battery.
  3. System board.
02F5DMA test failed.
  1. DIMM.
  2. System board.
02F6Software NMI failed
  1. DIMM.
  2. System board.
02F7Fail-safe timer NMI failed
  1. DIMM.
  2. System board.
1802Unauthorized network card is plugged in—Turn off and remove the miniPCI network card.
  1. Remove Mini PCI network card
  2. System board.
1803Unauthorized daughter card is plugged in—Turn off and remove the daughter card.
  1. Remove the daughter card that you installed.
  2. System board.
1804Unauthorized WAN card is plugged in—Power off and remove the WAN card.
  1. Remove the WAN card that you installed.
  2. System board.
1805Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card.
  1. Remove the Wireless USB card that you installed.
  2. System board.
1820More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system.Remove all but the reader that you set up for the authentication.
1830Invalid memory configuration—Power off and install a memory module to Slot-0 or the lower slot.Install DIMM in Slot-0, but not in Slot-1. Note: For the construction of the DIMM slot, see Memory removal and installation - ThinkPad T510, T510i, W510.
2000Hard Drive Active Protection sensor diagnostics failed.Press Esc to continue.Press F1 to enter SETUP
  1. Undock docking station or port replicator if it is attached to the ThinkPad Notebook.
  2. Place the ThinkPad Notebook on a horizontal surface. Do not apply any physical shock to the computer.
  3. Run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
2010Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed.Inform the following information to the customer: If in the primary bay the customer is using a non-IBM or non-Lenovo hard disk drive (HDD), or an old generation IBM HDD which is not supported by this system, with the risk in mind, the customer can still use it by pressing ESC. If in the primary drive bay the customer is using a supported IBM/Lenovo HDD with an old firmware, the customer needs to update its firmware to the latest. The latest version is available at http://www.lenovo.com/support
2100Initialization error on HDD0 (Main hard disk drive)
  1. Reseat the hard disk drive.
  2. Main hard disk drive.
  3. System board.
2102Initialization error on HDD1 (Ultrabay hard disk drive)
  1. Reseat the hard disk drive.
  2. Ultrabay™ hard disk drive.
  3. System board.
2110Read error on HDD0 (Main hard disk drive)
  1. Reseat the hard disk drive.
  2. Main hard disk drive.
  3. System board.
2112Read error on HDD1 (Ultrabay hard disk drive)
  1. Reseat the hard disk drive.
  2. Ultrabay hard disk drive.
  3. System board.

  • Alias ID:MIGR-74395
  • Document ID:HT001427
  • Last Updated :17/06/2014 10:33:02 p. m.
  • (c) 2014 Lenovo