제품 정보를 입력하면, 맞춤형 서비스를 이용할 수 있습니다.
제품이 선택되지 않았습니다.제품을 선택하십시오.
UEFI bootable USB media for installing Microsoft Windows 7 or Windows 8 64-bit operating systems on Lenovo Think Branded systems.
Symptom

Lenovo ThinkPads shipped with Microsoft Windows 8 preloads are configured in UEFI mode. Legacy-based boot media will not boot successfully on Think Branded Lenovo.

 

Affected Configurations

The above symptom is associated with, but not limited to, the following systems:

  • ThinkCentre
  • ThinkStation
  • ThinkServer
  • ThinkPad

Affected Systems (machine types, model types):

  • UEFI BIOS
Applies to
  • All Operating Systems
  • Microsoft Windows 7
  • Microsoft Windows 8
Solution

To create UEFI bootable USB media that can be used to install Microsoft Windows 7 or Windows 8 64-bit operating systems on Lenovo Think Branded computers, follow the steps below:

  1. Open a Command Prompt with Administrator privileges in either Windows 7 Pro or Windows 8 Pro.
  2. Insert the target USB boot media device into an available USB port.
  3. Type "DiskPart" in the command prompt.
  4. Type "List Disk” (make note of the disk number of the target USB drive).
  5. Type "Select Disk X”, where X is the target USB drive noted in step 4.
  6. Type "Clean”.
  7. Type "Create Partition Primary”.
  8. Type "format FS=fat32 quick”.
  9. Type "Active”.
  10. Type "Assign".
  11. Type "list volume".
  12. Type "Exit".

The user should copy the entire contents of the desired operating system onto the newly created UEFI boot media device.

If the AUTORUN.INF file fails to copy from the Windows DVD media to the USB key, then use Notepad to create a new AUTORUN.INF file on the USB boot media by following the steps below:

  1. Open the AUTORUN.INF file on the DVD media with Notepad and copy the contents.
  2. Create a new file on the USB media with Notepad and paste the contents from step 1.
  3. Save the file as "AUTORUN.INF".
Limitation

UEFI BIOS requires 64-bit versions of Windows operating systems.

Lenovo ThinkPad Tablet 2 has a 32-bit UEFI BIOS.

A 32-bit version of Windows 8 is required for the ThinkPad Tablet 2.

Additional Information

The USB boot media must be at least 4GB in capacity.

To install Microsoft Windows 7 or Windows 8 in UEFI mode, the 64-bit versions of the respective operating system DVD media will be required. A full Windows 7 or Windows 8 DVD media is required. An upgrade DVD may not function correctly during base operating installs.

To create UEFI bootable USB media that will launch an MDT deploy, follow steps 1 through 12 in the Solution and then follow the steps below:

  1. Copy the contents of the \boot folder and the \EFI folder from the Microsoft Windows 8 install DVD to the USB media.
  2. Create a folder called "Sources" on the USB media.
  3. Copy the LiteTouchPE_x86.wim from the MDT deploy share to the newly created "Sources" folder.
  4. Rename the LiteTouchPE_x86.wim to boot.wim.
  5. Boot the USB media to begin the MDT deploy.
Trademarks

Lenovo, ThinkCentre, ThinkStation, and ThinkPad are trademarks of the Lenovo Corporation in the United States, other countries, or both.

Microsoft, Windows, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.



원하시는 내용을 찾을 수 없는 경우, 아래의 방법을 시도해 보십시오:
1. Lenovo 검색
2. 제품 사용 방법 및 일반적인 문제해결 방법
3. Lenovo 지원 포럼
4. 기술 지원 콜센터

국가 상태
사용 가능Worldwide
가명 아이디 : SF13-T0008
문서 자료 ID : HT076615
Legacy Document ID : SF13-T0008
마지막 업데이트 :
© 2013 Lenovo. All rights reserved.
   
Select Task
 
Drivers & Software  
Guides & Manuals  
Diagnose & Fix  
Warranty & Services  
Parts  
Accessories  

추가 자료
도움말 인덱스
제품 사양 - PSREF
드라이버 목록
새로 배포된 드라이버 (RSS)
커뮤니티
커뮤니티 기술자료
커뮤니티 포럼
Windows 8 Support