|
| Device address conflict | - Load Setup Defaults in BIOS Setup Utility
- Backup battery
- System board
|
| Allocation error for device | - Load Setup Defaults in BIOS Setup Utility
- Backup battery
- System board
|
| Failing bits: nnnn | - DIMM
- System board
|
| Invalid system configuration data | - DIMM.
- System board.
|
| I/O device IRQ conflict | - Load Setup Defaults in BIOS Setup Utility
- Backup battery
- System board
|
| Operating system not found | - Check that operating system has no failure and is installed correctly
- Enter BIOS Setup Utility and see whether the hard drive and the diskette drive are properly identified
- Reseat the hard drive
- Check the boot sequence by use of BIOS Setup Utility
- Reinstall the operating system
- Diskette drive
- Hard drive
- System board
|
| Hibernation error | - Restore the system configuration to what it was the before the computer entered hibernation mode.
- If memory size has been changed, re-create the hibernation file.
|
| Fan error | Fan |
| Thermal sensing error | System board |
Unsupported memory
configuration | Shut down the computer and remove the extra memory. Maximum memory size is: - 256 MB for A21e series and the low-end models of A22e
- 512 MB for the high-end models of A22e
|
| Do you want abort resume from hibernation? (Y/N) System memory removed, press F3 to power off system and restore memory chip, press F4 to normal boot. | - Restore the system configuration to what it was before the computer entered hibernation mode
- If the memory size has been changed, re-create the hibernation file
|
| Docking station is removed or its ID is different, press F3 to power off system and restore correct docking station, press F4 to normal boot. | No error appears when; undock, hibernation, dock, wakeup. The docking is configured by the Operating System. |
| Authentication of system services failed. Press the Esc key to resume. | The Predesktop Area in the hard drive is corrupted. To use the Predesktop Area, restore it from a recovery CD. |
| CD ROM drive | - DIMM
- System board
|
| Entering SETUP | - DIMM
- System board
|
| Fixed disk n | - DIMM
- System board
|
| P/S 2 mouse boot summary screen | - DIMM
- System board
|
| One or more I2O block storage devices were excluded from the setup boot menu | - DIMM
- System board
|
| Parity Check 1 nnnn | - DIMM
- System board
|
| Parity Check 2 nnnn | - DIMM
- System board
|
| Press F1 to resume, F2 to Setup, F3 for previous | - DIMM
- System board
|
| Press F2 to enter Setup | - DIMM
- System board
|
| PS/2 Mouse | - DIMM
- System board
|
| Run the I2O Configuration Utility | - DIMM
- System board
|
| System BIOS shadowed | - DIMM
- System board
|
| UMB upper limit segment address: nnnn | - DIMM
- System board
|
| Video BIOS shadowed | - DIMM
- System board
|
| WRONG MEMORY: Serial Presence Detected (SPD) indicates 66MHz Memory. This processor requires 100MHz memory. Shut system down. | Shut system down.(Stop at this point). |
| Cannot boot from any device. | Check the status of device which you want to boot from.
Device not found. - The device you want to boot from.
- System board.
Device Error. - The device you want to boot from.
- System board.
No valid operating system. - Check that the operating system has no failure and is installed correctly.
- Reinstall the operation system.
Excluded from boot order. - Enter the BIOS Setup Utility and add the device in boot order.
|
Loading... Please Wait...
