1. System board. Replace planar.

System Security, the system has been tampered with.

1. Run BIOS Setup Utility, and then save current setting by pressing F10.
2. System board.

1. System board

1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save current setting by pressing F10.
   
2. System board.

1. Run BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save current setting by pressing F10.

EAIA data access error, the access to EEPROM is failed (read or write).

1. System board.

Invalid RFID serialization information area or bad CRC2, the EEPROM checksum is not correct (block #0, 1). EEPROM CRC2 is not correct (block #6).

1. System board.
   Replace system board. Box serial number needs to be reinstalled.

Invalid RFID configuration information area, the EEPROM checksum is not correct (block #4, 5).

1. System board.
   Replace system board. UUID needs to be reinstalled.

Critical low-battery error

1. Charge the battery pack.
2. Battery pack

System Security, Invalid Remote Change requested.

1. Run BIOS Setup Utility, and then save current setting by pressing F10.
2. System board.

System Security, Embedded Security hardware tamper detected.

1. System board.

1. RFID model only supervisor password.

1. RFID model only supervisor password.

1. To clear this error enter BIOS Setup Utility by entering the supervisor password, and select:
   1. Password
   2. Security Chip
   3. Clear Security Chip
2. Security chip.
3. System board.

1. To clear this error enter BIOS Setup Utility by entering the supervisor password, and select:
   1. Password
   2. Security Chip
   3. Clear Security Chip
2. Security chip.
3. System board.

Invalid remote change requested

1. The remote configuration for the security chip has failed. Confirm the operation and try again

System Security, Security password retry count exceeded.

1. Run BIOS Setup Utility, and then save current setting by pressing F10.
2. System board.

1. Remove either a Mini PCI modem card or an modem daughter card; or press Esc to ignore the warning message
2. System board.

1. Remove the Ethernet device that you installed;or press Esc to ignore the warning message.
2. System board.

Hard disk error, the Fixed disk is not working or not configured properly.

1. Reseat the hard disk
2. Load Setup Defaults in BIOS Setup Utility.
3. hard disk.
4. System board.

1. Enter here.

1. Run interactive tests of the keyboard and the auxiliary input device.

1. Replace keyboard controller.

1. Unlock the system to proceed.

Monitor type error, monitor type does not match the one specified in CMOS.

1. Load Setup Defaults in BIOS Setup Utility.

Shadow RAM error, shadow RAM fails at offset nnnn.

1. System board.

System RAM error, system RAM fails at offset nnnn.

1. DIMM.
2. System board.

Extended RAM error, extended RAM fails at offset nnnn.

1. DIMM.
2. System board.

System battery error, system battery is dead.

1. Replace the backup battery and run BIOS Setup Utility to reset the time and date.

System CMOS checksum bad, default configuration used.

1. Replace the backup battery and run BIOS Setup Utility to reset the time and date.

Password checksum bad. The password is cleared.

1. Reset the password by running BIOS Setup Utility.

System timer error

1. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
2. System board.

Real time clock error

1. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
2. System board.

Date and time error, neither the date nor the time is set in the computer.

1. Run BIOS Setup Utility to reset the time and date.

Previous boot incomplete, default configuration used.

1. Load "Setup Default" in BIOS Setup Utility.
2. DIMM.
3. System board.

1. Enter here.

1. Check to see that the drive is defined with the proper diskette type in Setup and that the diskette drive is attached correctly.

1. Check to see that the drive is defined with the proper diskette type in Setup and that the diskette drive is attached correctly.

1. Diskette drive.
2. External FDD cable.
3. I/O card.
4. Run setup.

1. Diskette drive.
2. External FDD cable.
3. I/O card.
4. Run setup

1. On older boards, check the cache jumpers. You may have to replace the cache

1. Load Setup Defaults in BIOS Setup Utility.
2. Replace the backup battery.
3. System board.

1. DIMM.
2. System board.

1. DIMM.
2. System board.

1. DIMM.
2. System board.

1. Shut down the computer and remove it from the docking station

Unauthorized network card is plugged in, power off and remove the Mini PCI network card

1. Remove Mini PCI network card
2. System board.

1. Remove the daughter card that you installed.
   
2. System board.

1. If the Access Predesktop Area has been previously disabled, then go the the BIOS Setup Utility by pressing F1 to open the BIOS Setup Utility. Select:
   1. Security
   2. Predesktop Area
   3. Access Predesktop Area, and then set this item to Disabled.
   4. Save and exit.
2. If the Access Predesktop Area has not been previously disabled, press Enter to load Access Predesktop Area. Then run RECOVER TO FACTORY CONTENTS in Access Predesktop Area.
3. If item 2 failed, press F3 in welcome screen in RECOVER TO FACTORY CONTENTS. Run FDISK, and then delete all partitions. Run RECOVER TO FACTORY CONTENTS in Access Predesktop Area again.
4. If item 3 failed, select CD-ROM boot in Startup in Access Predesktop Area. Boot from Recovery CD and perform full recovery from it.
5. If item 4 failed, replace the hard disk.