Print
login Account
Search
Unsupported Browser Detected: Dear user, the browser you’re currently using is not supported by this website. Please click here for more information about the browsers we support and how to obtain them.

Safety information to be familiar with before servicing a NetVista or ThinkCentre computer

Note: The service procedures are designed to help you isolate problems. They are written with the assumption that you have model-specific training on all computers, or that are familiar with the computers, functions, terminology, and service information provided.

Safety information
The following section contains the safety information that you need to be familiar with before servicing your computer.

General safety
Follow these rules to ensure general safety:
  • Observe good housekeeping in the area of the machines during and after maintenance.
  • When lifting any heavy object:
    1. Ensure you can stand safely without slipping.
    2. Distribute the weight of the object equally between your feet.
    3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
    4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any objects that weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.
  • Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
  • Before you start the machine, ensure that other service representatives and the customer’s personnel are not in a hazardous position.
  • Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine.
  • Keep your tool case away from walk areas so that other people will not trip over it.
  • Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
  • Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end.
  • Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
    Remember: Metal objects are good electrical conductors.
  • Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.
  • After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.
  • Reinstall all covers correctly before returning the machine to the customer.
Electrical safety

DANGER
Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures.

Observe the following rules when working on electrical equipment.

Attention: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.

Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

  • Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.
  • Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
  • Disconnect all power before:
    • Performing a mechanical inspection
    • Working near power supplies
    • Removing or installing main units
  • Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
  • If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
  • Ensure that another person, familiar with the power-off controls, is near you.
    Remember: Another person must be there to switch off the power, if necessary.
  • Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back.
    Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.
  • When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.
  • Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.
    Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.
  • Regularly inspect and maintain your electrical hand tools for safe operational condition.
  • Do not use worn or broken tools and testers.
  • Never assume that power has been disconnected from a circuit. First, check that it has been powered-off.
  • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds.
  • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
  • Do not service the following parts with the power on when they are removed from their normal operating places in a machine:
    • Power supply units
    • Pumps
    • Blowers and fans
    • Motor generators
    • and similar units. (This practice ensures correct grounding of the units.)
  • If an electrical accident occurs:
    • Use caution; do not become a victim yourself.
    • Switch off power.
    • Send another person to get medical aid.
Safety inspection guide
The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

  • Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock).
  • Explosive hazards, such as a damaged CRT face or bulging capacitor
  • Mechanical hazards, such as loose or missing hardware

The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected.

Checklist:

  1. Check exterior covers for damage (loose, broken, or sharp edges).
  2. Power-off the computer. Disconnect the power cord.
  3. Check the power cord for:
    1. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground.
    2. The power cord should be the appropriate type as specified in the parts listings.
    3. Insulation must not be frayed or worn.
  4. Remove the cover.
  5. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-IBM alterations.
  6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
  7. Check for worn, frayed, or pinched cables.
  8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling electrostatic discharge-sensitive devices
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

  1. Use product-specific ESD procedures when they exceed the requirements noted here.
  2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

  • Keep the parts in protective packages until they are inserted into the product.
  • Avoid contact with other people.
  • Wear a grounded wrist strap against your skin to eliminate static on your body.
  • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
  • Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.
  • Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

    Note: The use of a grounding system is desirable but not required to protect against ESD damage.
    • Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
    • Use an ESD common ground or reference point when working on a double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems.
    • Use the round ground-prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

 

Safety notices
Important: All caution and danger statements in this documentation begin with a number. This number is used to cross reference an English caution or danger statement with translated versions of the caution or danger statement in this section.

For example, if a caution statement begins with a number 1, translations for that caution statement appear in this section under statement 1.

Be sure to read all caution and danger statements before performing any of the instructions.

Statement 1
electrical danger

DANGER
Electrical current from power, telephone and communication cables is hazardous.

To avoid a shock hazard:

  • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
  • Connect all power cords to a properly wired and grounded electrical outlet.
  • Connect to properly wired outlets any equipment that will be attached to this product.
  • When possible, use one hand only to connect or disconnect signal cables.
  • Never turn on any equipment when there is evidence of fire, water, or structural damage.
  • Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.
  • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.
To Connect
  1. Turn everything OFF.
  2. First, attach all cables to devices.
  3. Attach signal cables to connectors.
  4. Attach power cords to outlet.
  5. Turn device ON.
To Disconnect
  1. Turn everything OFF.
  2. First, remove power cords from outlet.
  3. Remove signal cables from connectors.
  4. Remove all cables from devices.
Statement 2
caution

DANGER
When replacing the lithium battery, use only IBM part number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

Do not:

  • Throw or immerse into water
  • Heat to more than 100°C (212°F)
  • Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

Statement 3
caution

DANGER
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or transmitters) are installed, note the following:

Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.

Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.

caution

DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:

Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.

Statement 4
caution

safe lifting practices

DANGER
Use safe practices when lifting.

Statement 5
electrical danger

DANGER
The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

electrical danger

disconnect power cords

Statement 10
DANGER
Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices.

no heavy objects on top of rack mounted devices

Purchase parts online

  • Alias ID: NETV-SAFETY
  • Document ID: PD012787
  • Last Updated :2014-06-17
  • (c) 2014 Lenovo